Wright Serial #49705 and Higher Manuale Utente

Commercial Mower Owner’s Manual For Stander Serial Numbers 49705 and Higher Until Superseded WARNING: READ THIS MANUAL BEFORE USING Revise

9 level deck or a reverse pitched deck and this WILL compromise cut quality. (Refer to tire maintenance and pressure section) Fuel Safety Handl

10 OPERATING INSTRUCTIONS If you are not completely familiar with the Safety Instruction Manual read it now before proceeding with the operation of

11 acquainted with the operation of the hand controls and the mower’s behavior. After gaining a good feel for how the mower handles, gradually at

12 How to Adjust Neutral Neutral refers to the mower movement when the engine is set to full throttle, parking brake is off, and the control levers

13 How to Test/Use the Blade Clutch/Brake Switch Before testing the blade clutch/brake operation, make sure the area is clear and there is nothing

14 Belt Tension Adjustment The pump drive belt is self-adjusting, and requires no adjustment, just replacement. The blade drive belt is self-adjus

15 Hydro Oil Tank Check/Fill Checking oil • Ensure mower is on a level surface. • Lift hinged pad and remove hex socket plug from

16 the bypass valves open and the engine running, slowly move the control levers back and forth five or six times. Now close the bypass valves and

17 Critical Application ModelsThread LockerTorque Range (ft-lbs)Torque SticksWheel motor bolts (Securing motor to support)Big/Small Stander, RH, WSE

18 MAINTENANCE ITEMENGINE ITEMSSEE NOTE BELOWFIRST 8 HOURSDAILYEVERY 25 HOURSEVERY 100 HOURSEVERY 200 HOURSEVERY 300 HOURSANNUALLYInspect for cracks

1 Foreword Welcome to the progressive group of mowing professionals who use Wright mowers. We are focused on giving you advanced engineering and qua

19 Date Maintenance/Service PerformedUnit HoursShop/TechnicianMaintenance Record

20 P/N Description11990038 BOLT, HEX 5/8-11 X 9 Z5-STANDER 36/4212990003 NUT, HEX 5/8-11 Z FOR BLADES13990007 MACH BUSH 5/8 X 1 1/2 X 1/4 Z13990011

21 76490004 DECAL, STANDER 76490013 DECAL, MAIN INST. PANEL 76490005 DECAL, THROTTLE / INSTRUCTIONS (2) 76460001 DECAL, DANGER BLADE HA

22 Wright Manufacturing, Inc. (hereinafter: WMI) warrants to the original owner that the new WMI mower accompanying this document

23 Problem Description Possible Cause SolutionStreaking is when strips of uncut grass are left behind. Blades are not sharp Sharpen bladesBlades a

Notes:

Notes:

Notes:

4600X Wedgewood Blvd Frederick, MD 21703 www.wrightmfg.com

2 TABLE OF CONTENTS PRE-DELIVERY SERVICE OF MOWER BY DEALER ...

3 PRE-DELIVERY SERVICE OF MOWER BY DEALER Before proceeding with the Pre-Delivery Service of your mower, please read the safety instructions manual

4  Turn on the blade clutch switch. Run blades for approximately one minute. Next, engage and disengage the blades a few times about 10 seconds ap

5 SAFETY INSTRUCTIONS WRIGHT MOWER USERS & OWNERS: READ THIS MANUAL BEFORE USING PLEASE BE CAREFUL! Introduction This mower is built t

6 WARNING User Clothing DO NOT operate the mower while wearing sandals, tennis shoes, sneakers, or shorts. Always wear long non-baggy pant

7 use, never direct the grass discharge toward bystanders, traffic, cars or buildings nor allow anyone within 50 feet of the machine while in opera

8 Operation In Reverse Always keep a firm grip on the mower stationary handlebar with both hands. Keep both feet firmly on the foot platform.