Wright Serial #59542 and higher Manuale Utente

Wright Manufacturing Inc. Instruction Manual Wright Manufacturing 4600X Wedgewood Blvd Frederick, Md 21703 Wright ZTO serial # 59542 a

8 WARNING WARNING WARNING WARNING • The grass discharge chute deflector must be installed at all times and in the down position exce

9 WARNING WARNING 1.16 Operation on Slopes DO NOT operate on steep slopes. DO NOT operate the mower on slopes steeper than you can feel sec

10 WARNING WARNING 1.18 Hydraulic Safety The hydraulic system on the Wright ZTO is not equipped with high pressure hydraulic hoses or any ex

11 2 Warning, Safety and Instructional Decals • Specific safety warning decals are located on the equipment near immediate areas of potential hazard

12 Width (Deflector Down) 49" (59") / 124 cm (150 cm)Length 78" (198 cm)Weight 1015 lbs (460 kg)Width (Deflector Down) 53" (63&q

13 4 Machine Description & Overview The Wright ZTO is meant to solely cut, bag or mulch grass. The use for any other purpose is not recommended

14 4.1 Model and Serial Location 1. The plate is affixed on the right side in the engine compartment. 2. Stated on the plate will be the Model and s

15 4.3 Steering Control Levers The ZTO’s speed and direction are controlled by using two steering control handles. The handles can be moved forward

16 4.7 Deck Lift Lever The foot operated deck lift is used to raise and lower the deck. Deck is to be in the up position when in transport, go over

17 5 OPERATING INSTRUCTIONS If you are not completely familiar with the Safety Instruction Manual read it now before proceeding with the operation

Wright Manufacturing Inc. Foreword Welcome to the progressive group of mowing professionals who use Wright mowers. We are focused on giving you a

18 try moving the hand control levers, one at a time, very slightly, forward and backward. Gradually increase your speed until you are well acquain

19 5.6 Mowing on Varying Terrain See the Safety Instructions section of this manual, especially the parts on: • Initial Operating Safety Guidelin

20 WARNING After getting the mower to track straight, readjust the neutral adjustment on the pump by using a ¼” allen wrench at the Return-to-Ne

21 6.2 Height-of-Cut Before adjusting the height-of-cut be sure the mower blades are off, and the rear tires have proper air pressure. Check for ev

22 6.3 Belt Tension Adjustment The pump drive belt is self-adjusting, and requires no adjustment. The blade drive belt is self-adjusting also and re

23 WARNING WARNING 6.5 How to Move the Mower if the Engine Won’t Start Remove the R-clip from the neutral release arm (bypass valve). Pull

24 WARNING WARNING Left Transaxle Right Transaxle Expansion tank Filter Guard and Filter Filter Guard and Filter Expansion tank Vent Plug (a

25 WARNING WARNING 6.10 Cutting Blades In order to maintain to best cut, it is important that the blades are well sharpened and not damaged.

26 This symbol means ATTENTION! YOUR SAFETY IS INVOLVED. The message that follows the symbol contains important information about

27 Dust Filter Vent / Purge To Tank 6.14 Spindle and Drive Pulley Split hub R&R • Remove 2, ¼” bolts from split hub and install in threaded hol

1 TABLE OF CONTENTS PRE-DELIVERY SERVICE OF MOWER BY DEALER ...

28 6.16 Kawasaki / Briggs & Stratton Engine Manual / Maintenance It is very important that all users of this unit read and understand the Kawasa

29 Maintenance ChartFirst 5 Hours Change oilEvery 8 Hours or Daily Check engine oil level Clean area around muffler and controls Cle

30 7 Electrical Schematic

31 P/N Description13990007 BLADE SPACER, 5/8 X 1/417420012BUMPER, RUBBER, BLACK17460017CHUTE DEFLECTOR, RUBBER PC ONLY17460018 STRIPING RUBBER, ADJU

32 9 Decals

33 MAINTENANCE ITEMENGINE ITEMSSEE NOTE BELOWFIRST 8 HOURSDAILYEVERY 25 HOURSEVERY 100 HOURSEVERY 200 HOURSEVERY 300 HOURSANNUALLYInspect for cracks

34 Maintenance Record Date Maintenance/Service PerformedUnit HoursShop/Technician

35 Wright Manufacturing, Inc. (hereinafter: WMI) warrants to the original owner that the new WMI mower accompanying this document

36 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The United States Environmental Protection Agen

37 (2) Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period st

2 PRE-DELIVERY SERVICE OF MOWER BY DEALER Before proceeding with the Pre-Delivery Service of your mower, please read the safety instructions manual

38 Problem Description Possible Cause SolutionStreaking is when strips of uncut grass are left behind. Blades are not sharp Sharpen bladesBlades a

39 NOTES:

40 NOTES:

41 NOTES:

42 4600X Wedgewood Blvd Frederick, MD 21703 www.wrightmfg.com

3  Turn on the blade clutch switch. Run blades for approximately one minute. Next, engage and disengage the blades a few times about 10 seconds ap

4 1 Introduction This mower is built to the highest standards in the industry. However, carelessness or operator error may result in serious bodily

5 WARNING Do's Don'tsRead the operators manual before attempting to operate this machine Don't disable safety switchesUse all PPE

6 WARNING WARNING WARNING WARNING 1.5 Safety for Operation The ZTO should only be used by fully trained operators to prevent the ris

7 WARNING WARNING place and operating properly. Replace if the deflector becomes worn or ceases to properly deflect the grass in a safe man