Wright Serial #55142 and higher Manuale Utente

Wright Manufacturing Inc. Instruction Manual Wright Manufacturing 4600X Wedgewood Blvd Frederick, Md 21703 Mid Mount Z serial #55142

8 • All operators of this mower should exercise caution when driving this mower at high speeds. Sudden acceleration or deceleration may cause serio

9 1.14 Zero-Radius Turn Operation During zero-radius turns (when one mower wheel rotates backwards while the other rotates forward) drive extra slow

10 WARNING 1.16 Fuel Safety Handle gasoline with care – it is highly flammable. Do not smoke while handling gasoline. Use an approved gasolin

11 2 Warning, Safety and Instructional Decals • Specific safety warning decals are located on the equipment near immediate areas of potential hazard

12 Width, deflector down 63 inches (160 cm)Length 78 inches (198 cm)Height at ROP's 76 inches (193 cm)Weight 950 lbs (430.9 kg)52" Mid-Mou

13 4 Machine Description & Overview The Wright Mid-Mount Z is meant to solely cut, bag or mulch grass. The use for any other purpose is not rec

14 4.2 Steering Control Levers The Mid-Mount Z’s speed and direction are controlled by using two steering control handles. The handles can be moved

15 4.6 Deck Lift Lever The foot operated deck lift is used to raise and lower the deck. Deck is to be in the up position when in transport, go over

16 5 OPERATING INSTRUCTIONS If you are not completely familiar with the Safety Instruction Manual read it now before proceeding with the operation

17 WARNING 5.3 How to drive the mower While sitting, both feet should be firmly placed on the foot platform. Set the engine speed about a fourt

Wright Manufacturing Inc. Foreword Welcome to the progressive group of mowing professionals who use Wright mowers. We are focused on giving you a

18 so the left caster wheel comes over and last should be the right caster wheel as the mower is twisting to the left (counterclockwise). The techn

19 lengthening the right-side rod) or the left side needs to go slower (by shortening the left-side rod). It is important that neither rod should be

20 6.2 Height-of-Cut Before adjusting the height-of-cut be sure the mower blades are off, and the rear tires have proper air pressure. Check for ev

21 6.3.1 Replacing the Drive Belt • Stop the engine, remove the key and wait for all moving parts to stop. • Raise rear of the mower and secure. •

22 WARNING 6.5 How to Move the Mower if the Engine Won’t Start Rotate both of the hydro bypass valves on the front of each hydraulic pump about

23 WARNING 6.7 Oil Cooler Cleaning • Clean cooler before each use or daily. • Stop engine, wait for all moving parts to stop, remove key and a

24 ROLLOVER MAY CAUSE PERMANENT INJURY OR DEATH. • ROPS RAISES THE CENTER OF GRAVITY AND REDUCES STABILITY ON SLOPES. • SUDDEN STARTS OR TURNS ON

25

26 Machine Preparation 1. Park machine on a level surface and set brake. 2. Remove ROPS and hardware from shipping box and identify all parts us

27 12. Attach (1) nylon lanyard to the handle part of each hitch pin. Insert one end of the lanyard through the retaining washer and at

1 TABLE OF CONTENTS PRE-DELIVERY SERVICE OF MOWER BY DEALER ...

28 WARNING Dust Filter Vent / Purge To Tank 6.11 Transporting Use a heavy duty trailer or truck to transport the Mid-Mount Z. Lock brake and bl

29

30 6.15 Cleaning the Mower The underside of the mower deck should be checked and cleaned twice daily, and more often if the grass being mowed is lus

31 7 Electrical Schematic

32 8 Decals

33 MAINTENANCE ITEMENGINE ITEMSSEE NOTE BELOWFIRST 8 HOURSDAILYEVERY 25 HOURSEVERY 100 HOURSEVERY 200 HOURSEVERY 300 HOURSANNUALLYInspect for cracks

34 Maintenance Record Date Maintenance/Service PerformedUnit HoursShop/Technician

35 Wright Manufacturing, Inc. (hereinafter: WMI) warrants to the original owner that the new WMI mower accompanying this document

36 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The United States Environmental Protection Agen

37 (2) Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period st

2 PRE-DELIVERY SERVICE OF MOWER BY DEALER Before proceeding with the Pre-Delivery Service of your mower, please read the safety instructions manual

38 Problem Description Possible Cause SolutionStreaking is when strips of uncut grass are left behind. Blades are not sharp Sharpen bladesBlades a

39 NOTES:

40 NOTES:

41 NOTES:

42 4600X Wedgewood Blvd Frederick, MD 21703 www.wrightmfg.com

3  Move the engine throttle control to ¾ RPM speed setting.  Turn on the blade clutch switch. Run blades for approximately one minute. Next, enga

4 1 Introduction This mower is built to the highest standards in the industry. However, carelessness or operator error may result in serious bodily

5 Do's Don'tsRead the operators manual before attempting to operate this machine Don't disable safety switchesUse all PPE's, eye

6 WARNING WARNING WARNING WARNING WARNING 1.3 Important Information It is vital that these instructions are available to machine

7 WARNING WARNING the engine contrary to engine manufacturer specifications. Failure to comply can compromise operator safety, shorten equi