Wright 54700 and higher Manuale Utente

Commercial Mower Owner’s Manual For Stander Serial Numbers 54700 and Higher Until Superseded WARNING: READ THIS MANUAL BEFORE USING Revise

9 the mower very slowly, inching it backward until you become familiar with how the mower operates. Always operate slowly if in an awkward location

10 Note: Excessively worn tire tread is dangerous. Replace tire(s) with less than 3/32” of any tread groove left. Use tires with the tread patter

11 Critical ApplicationThread LockerTorque Range (ft-lbs)Wheel motor bolts (Securing motor to support) Loctite 2760 40-50Clutch to engine shaft Loct

12 3 Machine Description & Overview The Wright Stander is meant to solely cut, bag or mulch grass. The use for any other purpose is not recomme

13 3.1 Operator’s Area 1. Anti-Tip Wheels 2. Brake Handle 3. Caster Arms/Yokes

14 OFF ON 3.3 Digital Hour Meter The Stander is equipped with a digital hour meter. Refer to operating/reset instructions below. The programming s

15 3.6 Safety Interlock System The Wright Stander is equipped with a safety interlock system. The PTO must be disengaged, brake applied and control

16 4 OPERATING INSTRUCTIONS If you are not completely familiar with the Safety Instruction Manual read it now before proceeding with the operation

17 parking brake. The higher engine speed will make the controls much more responsive and the mower much quicker; Use caution if it is your first t

18 Slow Hole 4.7 How to Adjust Neutral Neutral refers to the mower movement when the engine is set to full throttle, parking brake is off, and the c

1 Foreword Welcome to the progressive group of mowing professionals who use Wright mowers. We are focused on giving you advanced engineering and qua

19 If the rod is made shorter it will increase the forward speed capability for that side of the mower and if the rod is made longer it will slow do

20 5 Service and Adjustments 5.1 Tire Maintenance and Pressure Excessively worn tire tread is dangerous on all hills. Replace drive tires with les

21 5.3 Belt Tension Adjustment The pump drive belt is self-adjusting, and requires no adjustment, just replacement. The blade drive belt is self-adj

22 5.4 Spring platform Adjustment The factory setting is both springs set at the most forward position. The more rearward t

23 Filling oil • Lift hinged pad and remove hex socket plug. • Using a funnel, fill tank through oil level port until oil reaches bottom threads of

24 . 5.11 Battery Service The battery is 12 volts and is a maintenance free battery. Charge the battery only if it will not

25 Critical Application ModelsThread LockerTorque Range (ft-lbs)Torque SticksWheel motor bolts (Securing motor to support)Big/Small Stander, RH, WSE

26 5.16 Fuel Evaporation System All Wright Standers need to have this mandatory feature. • Do Not alter or remove. • Do Not fill past the “Ma

27 MAINTENANCE ITEMENGINE ITEMSSEE NOTE BELOWFIRST 8 HOURSDAILYEVERY 25 HOURSEVERY 100 HOURSEVERY 200 HOURSEVERY 300 HOURSANNUALLYInspect for cracks

28 Date Maintenance/Service PerformedUnit HoursShop/TechnicianMaintenance Record

2 TABLE OF CONTENTS PRE DELIVERY SERVICE OF MOWER BY DEALER ...

29 P/N Description11990038 BOLT, HEX 5/8-11 X 9 Z5-STANDER 36/4212990003 NUT, HEX 5/8-11 Z FOR BLADES13990007 MACH BUSH 5/8 X 1 1/2 X 1/4 Z13990011

30 76490004 DECAL, STANDER 76490013 DECAL, MAIN INST. PANEL 76490005 DECAL, THROTTLE / INSTRUCTIONS (2) 76460001 DECAL, DANGER BLADE HA

32 Wright Manufacturing, Inc. (hereinafter: WMI) warrants to the original owner that the new WMI mower accompanying this document

33 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The United States Environmental Protection Agen

34 (2) Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period st

35 71440001 - BLADE 18" 71440002 - BLADE 16.5” 71440003 - BLADE 21” 71440008 - BLADE, FU

36 Problem Description Possible Cause SolutionStreaking is when strips of uncut grass are left behind. Blades are not sharp Sharpen bladesBlades a

37 NOTES:

Notes:

3 PRE-DELIVERY SERVICE OF MOWER BY DEALER Before proceeding with the Pre-Delivery Service of your mower, please read the safety instructions manual

4600X Wedgewood Blvd Frederick, MD 21703 www.wrightmfg.com

4  Turn on the blade clutch switch. Run blades for approximately one minute. Next, engage and disengage the blades a few times about 10 seconds ap

5 SAFETY INSTRUCTIONS WRIGHT MOWER USERS & OWNERS: READ THIS MANUAL BEFORE USING PLEASE BE CAREFUL! 1. Introduction This mower is buil

6 WARNING 1.2 Important Information It is vital that these instructions are available to machine users. It is also important to retain with th

7 operation. Be sure that all parts of the hand-operated hydraulic control system are tight and secure. This is to reduce the possibility that the

8 • Before leaving the operator’s position, even momentarily, turn off the blade clutch engagement switch and apply the parking brake. Keep others