Instruction Manual Wright Manufacturing 4600X Wedgewood Blvd Frederick, Md 21703 Large Frame Stander Serial 54956 and Higher WARNING:
9 WARNING WARNING WARNING WARNING WARNING • The grass discharge chute deflector must be installed at all times and in the down position ex
10 WARNING suddenly sliding sideways or down the hill. When operating on a slope, travel across the grade whenever possible, not in an up or down
11 WARNING WARNING 1.17 Using a Spark Arrester The engine in this machine is not equipped with a spark arrester muffler. It is in violation of
12 76490013, DECAL, MAIN INST. PANEL 2 Warning, Safety and Instructional Decals • Specific safety warning decals are located on the equipment near
13 Critical ApplicationThread LockerTorque Range (ft-lbs)Wheel motor bolts (Securing motor to support) Loctite 2760 40-50Clutch to engine shaft Loct
14 4 Machine Description & Overview The Wright Stander is meant to solely cut, bag or mulch grass. The use for any other purpose is not recomme
15 4.1 Operator’s Area 1. Anti-Tip Wheels 2. Brake Handle 3. Caster Arms/Yokes
16 4.3 Control Panel & Steering Control Levers The Stander speed and direction are controlled by using the control handles. Moving the control
17 4.6 Safety Interlock System The Wright Stander is equipped with a safety interlock system. The PTO must be disengaged, brake applied and control
18 WARNING WARNING 5 Operating Instructions If you are not completely familiar with the Safety Instruction Manual read it now before proceed
1 Foreword Welcome to the progressive group of mowing professionals who use Wright mowers. We are focused on giving you advanced engineering and qua
19 WARNING WARNING hand controls and the mower’s behavior. After gaining a good feel for how the mower handles, gradually attempt higher en
20 Slow Hole WARNING 5.7 How to Adjust Neutral Neutral refers to the mower movement when the engine is set to full throttle, parking brake is of
21 WARNING If the rod is made shorter it will increase the forward speed capability for that side of the mower and if the rod is made longer it
22 WARNING 6 Service and Adjustments 6.1 Tire Maintenance and Pressure Excessively worn tire tread is dangerous on all hills. Replace drive ti
23 6.3.2 Replacing the Drive Belt • Stop engine and remove the key and wait for all moving parts to stop. • Remove deck cove
24 OFF ON 6.4 Spring platform Adjustment The factory setting is both springs set at the most forward position. The more rearward the spring positio
25 Caster Arms/Pins Caster Wheel Bearings 6.7 Bleeding Air from the Hydraulic System Whenever servicing the hydraulic system, it is of the utmost im
26 6.10 Battery Service The battery is 12 volts and is a maintenance free battery. Charge the battery only if it will not start the mower properly.
27 WARNING 6.14 Loading and Unloading Use extreme caution when loading and unloading units on/off trailers or trucks.
28 WARNING 6.16 Spindle and Drive Pulley Split hub R&R • Remove 2, ¼” bolts from split hub and install in threaded holes in hub. • Slowly
2 TABLE OF CONTENTS PRE DELIVERY SERVICE OF MOWER BY DEALER ...
29 6.18 Kawasaki Engine Manual / Maintenance It is very important that all users of this unit read and understand the Kawasaki Engine Owner’s Manual
30 7 Electrical Schematic
31 76490004 DECAL, STANDER 76490013 DECAL, MAIN INST. PANEL 76490005 DECAL, THROTTLE / INSTRUCTIONS (2) 76460001 DECAL, DANGER BLADE HA
32 MAINTENANCE ITEMENGINE ITEMSSEE NOTE BELOWFIRST 8 HOURSDAILYEVERY 25 HOURSEVERY 100 HOURSEVERY 200 HOURSEVERY 300 HOURSANNUALLYInspect for cracks
33 Date Maintenance/Service PerformedUnit HoursShop/TechnicianMaintenance Record
34 P/N Description11990038 BOLT, HEX 5/8-11 X 9 Z5-STANDER 36/4212990003 NUT, HEX 5/8-11 Z FOR BLADES13990007 MACH BUSH 5/8 X 1 1/2 X 1/4 Z13990011
35 Wright Manufacturing, Inc. (hereinafter: WMI) warrants to the original owner that the new WMI mower accompanying this document
36 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The United States Environmental Protection Agen
37 (2) Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period st
38 Problem Description Possible Cause SolutionStreaking is when strips of uncut grass are left behind. Blades are not sharp Sharpen bladesBlades a
3 PRE-DELIVERY SERVICE OF MOWER BY DEALER Before proceeding with the Pre-Delivery Service of your mower, please read the safety instructions manual
Notes:
Notes:
4600X Wedgewood Blvd Frederick, MD 21703 www.wrightmfg.com
4 Turn on the blade clutch switch. Run blades for approximately one minute. Next, engage and disengage the blades a few times about 10 seconds ap
5 1. Introduction This mower is built to the highest standards in the industry. However, carelessness or operator error may result in serious bodil
6 Do's Don'tsRead the operators manual before attempting to operate this machine Don't disable safety switchesUse all PPE's, eye
7 WARNING WARNING WARNING WARNING WARNING 1.3 Important Information It is vital that these instructions are available to machine users. I
8 WARNING WARNING the equipment is in safe working condition. Check the blade mounting bolts for proper tightness every eight (8) hours of opera
Commenti su questo manuale